Sleeve-TITE Hex Head
Roll over image to zoom in
Sleeve-TITE™ Sleeve Anchor
304 Stainless Steel
This high-strength pre-assembled expansion anchor is designed for anchoring into concrete and masonry applications. The Sleeve-TITE anchor has a 6-dimple expansion sleeve over a threaded stud bolt, which provides superior performance in all conditions.
Downloads / Tech Flyer
Materials / Finishes
- Zinc-plated carbon steel
- Type 304 stainless steel
Features and Benefits
- 6-dimple expansion sleeve allows the anchor to grip imperfections in the base material
- Large expansion cone requires fewer rotations to achieve desired torque
- One-piece sleeve design allows stress to be distributed over the entire contact area
- Length identification code stamped on head to ease identification pre- and post-installation
- Pre-assembled with nut and washer for immediate installation, eliminating missing components
- Available in a number of head styles for a wide variety of applications
Installation
Part Numbers
Catalog Number
Head Style
Anchor Size
Drill Bit Dia.
Min. Embed.
Box Quantity
Carton Quantity
ASAX1413
Acorn Nut
1/4 x 1-3/8
1/4
1-1/8
100
1000
ASAX1421
Acorn Nut
1/4 x 2-1/4
1/4
1-1/8
100
800
HSAX5612
Hex Nut
5/16 x 1-1/2
5/16
1-3/16
100
800
HSAX5622
Hex Nut
5/16 x 2-1/2
5/16
1-3/16
100
800
HSAX3813
Hex Nut
3/8 x 1-7/8
3/8
1-1/4
50
400
HSAX3830
Hex Nut
3/8 x 3
3/8
1-1/4
50
400
HSAX3840
Hex Nut
3/8 x 4
3/8
1-1/4
50
400
HSAX1221
Hex Nut
1/2 x 2-1/4
1/2
1-1/2
25
200
HSAX1230
Hex Nut
1/2 x 3
1/2
1-1/2
25
200
HSAX1240
Hex Nut
1/2 x 4
1/2
1-1/2
25
200
HSAX5841
Hex Nut
5/8 x 4-1/4
5/8
2
10
80
FSAX1420
Flat Head
1/4 x 2
1/4
1-1/8
100
800
FSAX1430
Flat Head
1/4 x 3
1/4
1-1/8
100
800
FSAX3830
Flat Head
3/8 x 3
3/8
1-1/4
50
400
FSAX3840
Flat Head
3/8 x 4
3/8
1-1/4
50
400
FSAX3850
Flat Head
3/8 x 5
3/8
1-1/4
50
400
FSAX3860
Flat Head
3/8 x 6
3/8
1-1/4
50
400
BE3813
Brass Expansion Bolt
3/8 x 1-3/4
3/8
1-1/8
100
600
- Drill the hole perpendicular to the work surface. To assure full holding power, do not ream the hole or allow the drill to wobble.
- Drill the hole at least 1 anchor diameter deeper than the calculated embedment depth, but not closer than two anchor diameters to the
bottom surface of the concrete. Through drilling is allowed when 1 using sleeve anchors in hollow concrete block. - Clean the hole using compressed air and a nylon brush. A clean hole is necessary for proper performance.
- Drive anchor through the fixture into the hole making sure the nut, or head, rests solidly against the fixture. Be sure the anchor is set to the required embedment depth.
NOTE: Always wear safety glasses. Follow drill manufacturer's instructions. Use only solid carbide-tipped drill bits meeting ANSI B212.15 diameter standards.
