Ankr-TITE Stainless 316
Roll over image to zoom in
Ankr-TITE® Wedge Anchor
316 Stainless Steel
This pre-assembled high strength, fully threaded, and torque-controlled expansion anchor has a unique safety shoulder in the expansion cone that supports a thick 3-dimple clip engineered to provide high load carrying capability and reduce slip in a variety of installation conditions. Nut and washer included.
Downloads / Tech Flyer
Materials / Finishes
- Zinc-plated carbon steel with steel clip
- Hot-dip galvanized carbon steel with 304 stainless steel clip
- All 304 stainless steel
- All 316 stainless steel
Features and Benefits
- Length and identification code stamped on head to ease identification pre and post-installation
- Dog-point head prevents point damage during installation
- Fully threaded anchor body accommodates various application thickness
- Enlarged 3-dimple clip
- Increases response in lightweight concrete and requires fewer rotations to achieve desired torque
- 360 º segment contact on clip equalizes load distribution and increases load-carrying capacity
- Unique safety shoulder
- Supports the 3-dimple clip under maximum and ultimate loads, preventing slippage
- Similar products have gradual expansion cone that does NOT have a safety shoulder to support the clip when anchor is under strain
Installation
Part Numbers
Catalog Number
Anchor Size
Min. Embed. (in.)
Thread Length (in.)
Box Quantity
Carton Quantity
ATSS1413
1/4 x 1-3/4
1-1/4
3/4
100
800
ATSS1421
1/4 x 2-1/4
1-1/4
1-1/4
100
800
ATSS1431
1/4 x 3-1/4
1-1/4
2-1/4
100
800
ATSS3821
3/8 x 2-1/4
1-3/4
1
50
400
ATSS3823
3/8 x 2-3/4
1-3/4
1-1/2
50
400
ATSS3830
3/8 x 3
1-3/4
1-3/4
50
400
ATSS3833
3/8 x 3-3/4
1-3/4
2-1/2
50
400
ATSS3850
3/8 x 5
1-3/4
3-1/4
50
400
ATSS3870
3/8 x 7
1-3/4
4-1/2
50
300
ATSS1223
1/2 x 2-3/4
2-1/8
1-1/8
25
200
ATSS1233
1/2 x 3-3/4
2-1/8
2-1/8
25
200
ATSS1241
1/2 x 4-1/4
2-1/8
2-5/8
25
200
ATSS1242
1/2 x 4-1/2
2-1/8
2-5/8
25
200
ATSS1252
1/2 x 5-1/2
2-1/8
3-3/4
25
150
ATSS1270
1/2 x 7
2-1/8
4-1/2
25
150
ATSS1282
1/2 x 8-1/2
2-1/8
5
10
40
ATSS1210
1/2 x 10
2-1/8
5
10
40
ATSS5832
5/8 x 3-1/2
2-5/8
1-1/2
10
80
ATSS5841
5/8 x 4-1/4
2-5/8
2-3/8
10
80
ATSS5842
5/8 x 4-1/2
2-5/8
2-5/8
10
80
ATSS5850
5/8 x 5
2-5/8
3-1/8
10
80
ATSS5860
5/8 x 6
2-5/8
4
10
80
ATSS5870
5/8 x 7
2-5/8
4-1/2
10
80
ATSS5882
5/8 x 8-1/2
2-5/8
5
10
40
ATSS5810
5/8 x 10
2-5/8
5
10
40
ATSS3441
3/4 x 4-1/4
3-1/4
5
10
80
ATSS3443
3/4 x 4-3/4
3-1/4
2-1/2
10
80
ATSS3452
3/4 x 5-1/2
3-1/4
3-1/4
10
60
ATSS3461
3/4 x 6-1/4
3-1/4
3-3/4
10
60
ATSS3470
3/4 x 7
3-1/4
4-3/4
10
60
ATSS3482
3/4 x 8-1/2
3-1/4
5
10
40
ATSS3410
3/4 x 10
3-1/4
5
10
40
ATSS3412
3/4 x 12
3-1/4
5
5
20
ATSS7860
7/8 x 6
3-7/8
3-1/2
5
30
ATSS7880
7/8 x 8
3-7/8
5
5
20
ATSS7810
7/8 x 10
3-7/8
5
5
20
ATSS1060
1 x 6
4
3
5
30
ATSS1090
1 x 9
4
5
5
20
ATSS1012
1 x 12
4
5
5
20
- Drill the hole, whose diameter equals the anchor diameter, perpendicular to the work surface. To assure full holding power, do not ream the hole or allow the drill to wobble.
- A clean hole is necessary for proper performance. Clean the hole using a nylon brush and compressed air.
- Assemble the nut and washer onto the anchor. Drive the anchor through the material to be fastened at the calculated embedment depth.
- Tighten the nut, or head, 3 to 5 turns past the hand tight position. Installing with a torque wrench is recommended for optimum performance. Refer to Recommended Setting Torque* in the table below.
Drill the hole deeper than the intended embedment, but not closer than two diameters to the opposite surface of the concrete.
NOTE: Always wear safety glasses. Follow drill manufacturer's instructions. Use only solid carbide- tipped drill bits meeting ANSI B212.15 diameter standards.
